BookmarkBookmark
Sign In | Creat An Account  Help
Wholesale jewelry,your satisfaction our business
Home >>Rhinestone Earring Jewelry >> A kind of home made inspiration design of bracelet
Category Jewelry News
Tags:

A kind of home made inspiration design of bracelet


Confetti, this chunky bracelet is reason to celebrate. Its dynamic look is achieved by suspending hand-cut acrylic dots in the resin as it harden. Follow the step by step as below:

Materials: Polyester film; permanent marker; transparent tape; 3.2mm thick acrylic sheets in various colors; sandpaper, 100, 200, 320, and 400 grit; polyester casting resin and catalyst; stir sticks; extra fine steel wool; plastic wax.
Tools: scissors, hot glue gun, jeweler’s saw with 1/0 blades; safely equipments; measuring cups mark with ounces; bamboo skewers; coarse file; soft cloth.

Project step:  
-    Begin making a mold by cutting a 5x6 inch piece of polyester film. Using the permanent markers to draw a circle that is 2 1/2 inches in diameter inside the polyester film. The circle will serve as a guide for the inside of the bracelet and can be adjusting for different sizes. Draw the outline of the desired exterior shape.
-    Cut a strip of polyester film that measures 1 1/2 x 8 1/2 inches. Form the strip into a loop that fits inside the circle draw on the sheet. Tape the ends of the loop and burnish the tape to get a good seal. Cut another strip of polyester film that measures 1 1/2 x 13 inches and form it into a loop to fit the exterior shape. Secure the ends with tapes, applying the tape to the inside of the loop. Burnish the tape, and cut off any excess film.
-    Place the smaller loop on the base sheet. Use the glue gun to tack down the inside of the loop in several places with the circle serving as a guide. When the glue has set, apply glue all along the bottom of the inside seam and then along the outside seam. Check the seams to make sure they are securely sealed so the resin won’t seep out later during the casting process.
-    To make the inclusion, sand the surface of the acrylic sheets with 220 grit sandpaper to ensure that the casting resin will adhere sufficiently later, then use the jeweler’s saw to cut out small shapes out of the plastic. As you make the pieces, arrange them to a circle to get an idea of how they will look in the bracelet and how much space they’ll occupy.     
-    Arrange the acrylic pieces around the mold before you mix the coasting resin. Put on your safety gear, and measure out 3 ounces of resin.
-    Fill the mold halfway with resin to allow for the space the acrylic pieces will take up. Place the inclusions into the resin as you prearranged them. The pieces will sink to the bottom of the mold, so keep adding more. Using a bamboo skewer to adjust the pieces and to tease out air bubbles that might form. Allow the casting to set up for 24 hours before removing it from the mold.
-    Once the resin has set up, tear away the polyester film mold from the casting. Finally, work a bit of plastic wax over the surface with a soft cloth. The bracelet will bring out the colors of the acrylic and the transparency of the resin.

order cialis online
order cialis online
viagra
viagra
levitra
generic levitra 20mg
generic levitra 20mg
does levitra really work
does levitra really work
levitra side effects nih
levitra side effects nih
where to buy levitra online
where to buy levitra online
levitra pharmacy price
levitra pharmacy price
what happens if a woman takes viagra
what happens if a woman takes viagra
mexico viagra price
mexico viagra price
does viagra pills go bad
does viagra pills go bad
who makes generic levitra
levitra side effects high blood pressure
generic cialis malaysia
generic cialis malaysia
cialis online sales
cialis price in mexico
New Arrival
Home About us Rhinestone Earrings Jewelry Jewelry warehouse Wholesale western jewelry Bead Jewelry Wholesale Pearl Jewelry  Jewelry News
cute belly button rings turtle belly button rings long feather earrings cartier love bracelet heart friendship bracelet wholesale jewelry making supplies